39
loading...
Sparse Files in Windows, Linux and MacOS, and NTFS, REFS, Ext3, Ext4, BTRFS and APFS File Systems
In today’s article, we are going to deal with sparse files. You’ll learn about their pros and cons, and the file systems that support such files, and how to create them, or turn ordinary files into sparse ones.
Sparse files are special files that use the file system more efficiently and keep the file system from taking up free disk space when it is not filled with actual data. That is, “free disk space” will only be used when necessary. The “empty” data in the form of zeroes will be stored in the metadata block of the file system. That is why sparse files originally take up less space than their real size is.
This file type is supported by most file systems: BTRFS, NILFS, ZFS, NTFS[2], ext2, ext3, ext4, XFS, JFS, ReiserFS, Reiser4, UFS, Rock Ridge, UDF, ReFS, APFS, F2FS.
All these file systems support this type completely, but at the same time, they don’t provide any direct access to their functions through the standard interface. You can manage their properties with the command prompt only.
All file systems I have mentioned before also support the standard feature of compression. Both tools give you the advantage of saving disk space, but they achieve this goal in different ways. The main downside of using file compression is that affects system performance when reading or writing such files because the system needs extra resources to compress or decompress the data. However, some software products don’t support compression.
YouTube:
The biggest advantage of sparse files is that users can create very large files which take very little disk space. The space for storing data is allocated automatically as more and more information is written. Large sparse files are created relatively quickly because the file system doesn’t have to pre-allocate disk space for writing zeros.
However, the advantages of sparse files are limited to the applications that support them. If a certain program cannot recognize or use such files, it will save a sparse file in its original – uncompressed – form, and there’s no advantage to talk about. Users have to be careful when dealing with such files: a sparse file of a few megabytes may suddenly turn into a several-gigabyte monster when an application that doesn’t support this file type copies it into a directory.
One more disadvantage is that you can’t copy or create a sparse file if its nominal size exceeds the amount of available free space (or quota restrictions applied to user accounts within the operating system). For example, if the original size of a sparse file (with all of its zero bytes) is 500 MB, and the quota limit for the user account where this sparse file is created is only 400 MB, such situation generates an error, even if the actual disk space occupied by this sparse file is only 50 MB.
As to the hard disks where such data is stored, they are also subject to fragmentation, because the file system will write data to sparse files as and when necessary. Over time, it may result in reduced performance. Besides, some disk management utilities may have issues with displaying free disk space. When the file system containing files of this specific type is low on space, it may lead to unpredictable situations. For example, it may generate disk overfill issues when data is copied over the existing part of the file which is marked as sparse.
In Windows, we’ll be using the command prompt for this purpose. Type “cmd” in the search field and run it as Administrator.
In Windows, sparse files are managed with the help of fsutil tool (a file system utility). When the command create is performed, by default it creates a file that is not a sparse one. Go to the folder where you need to create a file and type the following:
fsutil file createnew sparse-file 1000000000Where sparse-file is the file name, and the number at the end is the file size in bytes.
To assign the “sparse” attribute to the file, use this command:
fsutil sparse setflag sparse-file
Here is the command to remove this attribute:
fsutil sparse setflag sparse-file 0
And here’s another one if you want that attribute back:
fsutil sparse setflag sparse-fileLet’s check it:
fsutil sparse queryflag sparse-file
The attribute by itself doesn’t let you start saving disk space. To make it happen, you need to set the empty space which should be freed inside the file.
Type this to set the empty space:
fsutil sparse setrange sparse-file 0 1000000000
At the end of the command, the offset and length are given in bytes. In my case, this is the range from zero to 1 GB.
To set a fully sparse file, specify the whole capacity. You can expand the file if necessary by typing a larger value.
To make sure the file has been assigned this attribute, run the command layout
fsutil file layout sparse-file
The sparse attribute can be assigned to any file by just running this command with the corresponding file’s name.
In the properties of the file we have created earlier, you can see that with the size of 1 GB this file occupies 0 bytes on disk.
This set of commands works with all Windows file systems that support sparse files (NTFS, ReFS, and so on).
In Linux, the process of creating such data types is a bit easier, because there are several commands to create them. They work fine with all Linux file systems.
Here, you can use either command: dd, or truncate.
The first command looks like this:
dd if=/dev/zero of=file-sparse bs=1 count=0 seek=2GWhere “file-sparse” is the file name, and the number at the end is the size that can be set in bytes, megabytes, and so on.
The second command is simpler:
truncate -s2G file-sparseWhere the “s” value stands for the file size, and it is followed by the file name.
Contrary to Windows, when you create a file with either command it will be a sparse file by default.
To turn an ordinary file into a sparse one, there is a special command:
cp --sparse=always ./025.jpg ./0251.jpgWhere 025.jpg is the name of the first file, an ordinary one,
and 026.jpg is the name of the second file, a sparse one.
How to expand a file
If you need to expand an existing file, use the first command below: replace the name and specify the size you need.
If you need to expand an existing file, use the first command below: replace the name and specify the size you need.
dd if=/dev/zero of=025.jpg bs=1 count=0 seek=2GThis command will increase its size to 2 GB.
Use the following command to check the size:
du -h --apparent-size 025.jpgIn fact, this set of commands also works with the Apple file system – ApFS, as Linux and MacOS are based on the Unix core architecture and they both provide access to Unix commands and the Bash command shell.
Launch the Terminal and run any command for creating a sparse file that I have just used in Linux.
In MacOS Catalina, only the first command is supported, and the size should be given in bytes, otherwise the command will generate an error.
sudo dd if=/dev/zero of=sparse_APFS bs=1 count=0 seek=1000000000
When certain conditions are observed, the ApFS file system creates sparse files by default, so you can expand any file with the command used to increase the size of sparse files in Linux:
dd if=/dev/zero of=187.jpg bs=1 count=0 seek=500000000Let’s set the size of 500 MB, and remember that in MacOS this size should be specified in bytes.
When you run the command and open file properties, you can see that its size has increased to 500 MB.
Watch the full article with all additional video tutorials. Also visit our Youtube channel, there are over 400 video tutorials.
39